Structural Fire Damage Cleaning in Gholson, TX
The drywall is gone, and now you are staring at blackened studs, scorched joists and a charred roof deck. Somebody now has to decide what gets blasted clean, what gets sistered and what gets replaced. Unify Fire Solutions connects you with independent, licensed and insured contractors in Gholson who clean the framing, masonry and steel itself.
- Soda, dry ice and hand cleaning of framing
- Every stud and joist probed for char depth
- Sealer applied to lock in residual odor
Why the Bare Structure Needs Its Own Crew
Close up the walls over dirty framing and the smoke odor bleeds right back through the new finish. This stage decides whether your rebuilt rooms smell fresh or smell burned for years.
Licensed & Insured Independent Pros
The contractors we connect you with are independent businesses carrying their own license and insurance. Verify both, and ask whether the crew follows the IICRC S700 standard for fire and smoke work.
Upfront Written Estimates
Blasting is priced by surface area, media and access, and attics and crawlspaces cost more to reach. Get a written, itemized estimate in hand before any blasting begins.
Rapid Local Dispatch
Day or night, a dispatcher picks up and starts looking for a structural cleaning crew right away. Timing depends on which crews near Gholson are free, and it is often the same day.
Blasting Rigs and Probing Tools
Structural crews bring soda blast pots, dry ice units, big compressors, HEPA vacs, air scrubbers and a sharp awl to test every member.
Do not climb into a burned attic or walk a scorched roof deck to look for yourself. Burned joists and decking can fail under one person's weight, and open wiring may still carry current. Let the crew confirm the structure will hold before anyone goes up, and keep everyone off the floor above a burned basement or crawlspace.
Cleaning the Building From the Roof Deck Down
This is not contents cleaning and it is not debris haul-out. This page is about the framing, masonry and steel that actually carry the load.
Char Depth Probing and Member Decisions
An awl pushed into a charred stud tells the story: if it stops in sound wood after a thin layer of char, the member is usually a cleaning candidate. Deep char that eats into the section of a joist or truss chord means sistering or replacement.
- Members marked clean, sister or replace
- Structural engineer called in for questionable beams, trusses and headers
- Photos of each marked member for the claim
Soda Blasting
Sodium bicarbonate is softer than wood, so it strips soot and light char off studs, joists and roof decking without gouging the grain. Expect fine dust and residue that has to be contained and HEPA vacuumed when the blasting is done.
Dry Ice Blasting
Dry ice pellets hit the surface and turn straight into gas, so there is no media left behind to sweep up. It suits cramped attics and areas around wiring, but it runs louder and pricier than soda.
- Hearing protection and ventilation required
- Good choice when residue would be a problem
Wire Brushing and Sanding
Small, isolated char spots are often handled by hand with wire brushes and sanders tied into a HEPA vacuum. Hand work is slower but sensible where a blast rig would be too much.
Brick, Block, Concrete and Steel Beams
Fireplace surrounds, block foundation walls and concrete slabs hold soot in their pores, and alkaline cleaners, scrubbing or blasting pull it out. Steel beams get cleaned and inspected for any heat warping, with doubts sent to the engineer.
Encapsulation and Attic Insulation Removal
Even well-blasted wood can hold faint odor in its pores, so crews roll or spray a pigmented shellac-based or specialty encapsulating sealer over cleaned framing. Attic jobs start by vacuuming out the smoky blown-in or batt insulation so the rafters and roof deck can be reached.
Under the house, the crew probes the joists, sill plates and subfloor underside, then blasts and seals what can stay. Expect a vapor barrier to be pulled and replaced if smoke or hose water soaked it.
Have the contractor explain the method they plan for each part of the house. It is common to see soda in open walls, dry ice in the attic and hand sanding near the electrical panel on the same job.
Plan for containment, because blasting throws soot and media into every corner it can reach. Expect poly over openings, taped-off HVAC returns and air scrubbers pulling the space under negative pressure during blasting. Ask how they will protect finished rooms and windows that were not damaged.
Looking at Blackened Studs and Rafters?
Ring the dispatch line and we start finding a structural cleaning crew near Gholson. It costs nothing to call.
Call +1-833-336-1630How a Structural Cleaning Job Unfolds
- 1
Phone the Dispatcher
Describe what is exposed: open stud walls, an attic, a crawlspace, block or steel. Let us know if an adjuster, engineer or roofer has already visited.
- 2
Mobile Crew on Site
An independent crew shows up with its compressor, blast gear, poly and air scrubbers. First they confirm the roof deck and floors will hold weight and that the exposed circuits are dead.
- 3
Probe, Mark and Quote
Every exposed member gets probed with an awl and marked clean, sister or replace, and anything borderline goes to a structural engineer. You get a written, line-item quote listing square footage, method, sealer and insulation removal before any work starts.
- 4
Blasting, Sealing and Walkthrough
After blasting and HEPA cleanup, the framing gets its sealer coat, and you walk the bare structure with the crew lead. Do a sniff test on a warm afternoon, and ask for photos of every marked member before the rebuild closes the walls.
Notes From People We Connected
After the attic fire, the rafters were black and the blown-in insulation was a wet mess. They vacuumed out the insulation, dry iced the rafters around the wiring and sealed it all. Two rafters were cut deep enough that they called in an engineer, and those got sistered.
I assumed every black stud in the hallway had to be replaced. The crew lead pushed an awl into each one and showed me the wood was solid under a thin crust. Soda blasting and a coat of sealer saved most of the wall.
The fire in our lower level left the block walls and the steel beam coated in soot. They scrubbed and blasted the block, cleaned the beam and had the engineer confirm it had not sagged. The basement smells normal again, even closed up.
Your Structural Fire Cleaning Questions Answered
How do crews decide if a charred stud can stay?
They probe it. Push an awl into the char, and if it hits solid wood after a shallow layer, the stud is usually a cleaning job. Members with deep char, splitting or a lost cross section get sistered or replaced, and anything structural in doubt goes to a licensed structural engineer.
What is the difference between soda blasting and dry ice blasting?
Soda media is mild on the grain and helps with odor, though it leaves a white dust that needs a full HEPA cleanup. Dry ice pellets vanish on impact, so cleanup is easier and it works well around wiring, but it is louder and usually costs more. Many crews use both on the same house.
Why seal the framing if it has already been cleaned?
Wood is porous, and smoke molecules sit deep in the grain where no blasting can reach. A shellac-based or specialty encapsulant locks that residual odor in so it cannot off-gas through the new drywall. Sealer only works over clean framing, never as a shortcut over soot.
Does the attic insulation have to come out after a fire?
In most cases where smoke got into the attic, it does. Loose-fill and batts act like a giant filter for smoke, and hose water often soaks them as well. Crews vacuum it out with a truck-mounted or portable insulation vac so the rafters and decking can be inspected and cleaned before new insulation goes in.
Can soot be cleaned off brick and concrete block?
Most of the time, but brick and block hold soot in their pores and need more than a wipe. Crews use alkaline masonry cleaners and stiff brushes, and soda or other media blasting for heavy buildup. Heat-cracked or spalled block and brick should be looked at by an engineer or mason.
Do I need a structural engineer for fire-damaged framing?
Not for every job, but for anything load-bearing that looks questionable, yes. Trusses, beams, headers, steel and heavily charred joists are where an engineer's letter protects you and helps the claim. The building department may ask for it before signing off on the rebuild.
Structural Fire Cleaning Throughout Gholson
Our dispatch line covers Gholson and the nearby communities around it, from older homes with plaster and solid-sawn joists to newer builds with engineered trusses. Attics, basements, crawlspaces, garages and light commercial spaces all come up regularly.
- Attic fires
- Electrical fires
- Furnace puff-backs
- Chimney fires
- Lightning strikes
- Neighbor's fire spread
If the first crew we connect you with is not the right fit, call back and a dispatcher will connect you with another. Do not let the rebuild close walls over dirty framing.
